.. _everest_modules_PhyVersoBSP:

###########
PhyVersoBSP
###########
| Driver module for Phytec PhyVerso EV Charging controller with Pionix MCU firmware


For a detailed handwritten documentation see :ref:`here <everest_modules_handwritten_PhyVersoBSP>`

********************
Module Configuration
********************
| **serial_port**:*string* <optional>
| *default: "/dev/ttyUSB0"*
|  Serial port the hardware is connected to
| **baud_rate**:*integer* <optional>
| *default: 115200*
|  Serial baud rate to use when communicating with the hardware
| **reset_gpio**:*integer* <optional>
| *default: -1*
|  If set <0 it is disabled. If > 0, configured reset_gpio_bank and reset_gpio_pin configuration is used for hard reset of MCU
| **conn1_max_current_A_import**:*integer* <optional>
| *default: 16*
|  Maximum import current in amps
| **conn1_min_current_A_import**:*integer* <optional>
| *default: 6*
|  Minimum import current in amps
| **conn1_min_phase_count_import**:*integer* <optional>
| *default: 3*
|  Minimum phase count for import
| **conn1_max_phase_count_import**:*integer* <optional>
| *default: 3*
|  Maximum phase count for import
| **conn1_min_current_A_export**:*integer* <optional>
| *default: 0*
|  Minimum export current in amps
| **conn1_max_current_A_export**:*integer* <optional>
| *default: 0*
|  Maximum export current in amps
| **conn1_min_phase_count_export**:*integer* <optional>
| *default: 3*
|  Minimum phase count for export
| **conn1_max_phase_count_export**:*integer* <optional>
| *default: 3*
|  Maximum phase count for export
| **conn1_has_socket**:*boolean* <optional>
| *default: False*
|  Set to true if it has a socket, false if it has a permanently attached cable
| **conn1_dc**:*boolean* <optional>
| *default: False*
|  Set to true if it is for DC, false if it is AC
| **conn2_max_current_A_import**:*integer* <optional>
| *default: 16*
|  Maximum import current in amps
| **conn2_min_current_A_import**:*integer* <optional>
| *default: 6*
|  Minimum import current in amps
| **conn2_min_phase_count_import**:*integer* <optional>
| *default: 3*
|  Minimum phase count for import
| **conn2_max_phase_count_import**:*integer* <optional>
| *default: 3*
|  Maximum phase count for import
| **conn2_min_current_A_export**:*integer* <optional>
| *default: 0*
|  Minimum export current in amps
| **conn2_max_current_A_export**:*integer* <optional>
| *default: 0*
|  Maximum export current in amps
| **conn2_min_phase_count_export**:*integer* <optional>
| *default: 3*
|  Minimum phase count for export
| **conn2_max_phase_count_export**:*integer* <optional>
| *default: 3*
|  Maximum phase count for export
| **conn2_has_socket**:*boolean* <optional>
| *default: False*
|  Set to true if it has a socket, false if it has a permanently attached cable
| **conn2_dc**:*boolean* <optional>
| *default: False*
|  Set to true if it is for DC, false if it is AC
| **reset_gpio_bank**:*integer* <optional>
| *default: 1*
|  GPIO peripheral bank the nRST pin of the MCU is mapped to
| **reset_gpio_pin**:*integer* <optional>
| *default: 23*
|  GPIO peripheral pin the nRST pin of the MCU is mapped to
| **conn1_motor_lock_type**:*integer* <optional>
| *default: 2*
|  Connector 1 motor lock type; 1 == Hella Style time-based lock, 2 == Valeo potentiometer feedback based
| **conn2_motor_lock_type**:*integer* <optional>
| *default: 2*
|  Connector 2 motor lock type; 1 == Hella Style time-based lock, 2 == Valeo potentiometer feedback based
| **conn1_gpio_stop_button_enabled**:*boolean* <optional>
| *default: False*
|  Set to true to enable external charging stop button for connector 1 on a GPIO connected to the SOM
| **conn1_gpio_stop_button_bank**:*string* <optional>
| *default: "gpiochip1"*
|  GPIO peripheral bank for connector 1 stop button
| **conn1_gpio_stop_button_pin**:*integer* <optional>
| *default: 36*
|  GPIO peripheral pin for connector 1 stop button
| **conn1_gpio_stop_button_invert**:*boolean* <optional>
| *default: False*
|  Set to true to invert pin logic
| **conn2_gpio_stop_button_enabled**:*boolean* <optional>
| *default: False*
|  Set to true to enable external charging stop button for connector 2 on a GPIO connected to the SOM
| **conn2_gpio_stop_button_bank**:*string* <optional>
| *default: "gpiochip1"*
|  GPIO peripheral bank for connector 2 stop button
| **conn2_gpio_stop_button_pin**:*integer* <optional>
| *default: 37*
|  GPIO peripheral pin for connector 2 stop button
| **conn2_gpio_stop_button_invert**:*boolean* <optional>
| *default: False*
|  Set to true to invert pin logic

********
Provides
********
| **connector_1**::ref:`evse_board_support <everest_interfaces_evse_board_support>`
|  provides the board support interface to low level control the proximity and control pilots, relais and motor lock
| **connector_2**::ref:`evse_board_support <everest_interfaces_evse_board_support>`
|  provides the board support interface to low level control the proximity and control pilots, relais and motor lock
| **rcd_1**::ref:`ac_rcd <everest_interfaces_ac_rcd>`
|  RCD interface of the onboard RCD
| **rcd_2**::ref:`ac_rcd <everest_interfaces_ac_rcd>`
|  RCD interface of the onboard RCD
| **connector_lock_1**::ref:`connector_lock <everest_interfaces_connector_lock>`
|  Lock interface
| **connector_lock_2**::ref:`connector_lock <everest_interfaces_connector_lock>`
|  Lock interface
| **phyverso_mcu_temperature**::ref:`phyverso_mcu_temperature <everest_interfaces_phyverso_mcu_temperature>`
|  Temperatures from MCU
| **system_specific_data_1**::ref:`generic_array <everest_interfaces_generic_array>`
|  Opaque data blobs coming from connector 1
| **system_specific_data_2**::ref:`generic_array <everest_interfaces_generic_array>`
|  Opaque data blobs coming from connector 2


********
Metadata
********
Authors
=======
| Cornelius Claussen

License
=======
| https://opensource.org/licenses/Apache-2.0